中埋式止水带接头检查方法：
Inspection method for joint of buried water stop belt:
1、检查中埋式橡胶止水带接头处上下的压茬方向，此方向应以排水畅通、降水外引为正确方向。
1. Check the direction of stubble at the joint of buried rubberwater stop belt. The direction should be smooth drainage andprecipitation introduction.
2、检查中埋式止水带接头的强度，抗拉伸强度不能低于母体的80%，不合格的地方应重新焊接或者粘结。简单的方法是用手轻轻的撕扯。
2. Check the strength of the joint of buried water stop tape.The tensile strength should not be lower than 80% of the parentbody. The unqualified parts should be re-welded or bonded. Theeasiest way is to tear it gently with your hand.
3、 检查接头表面的打毛情况。接头外观应平整光洁。
3. Check the grooming of the joint surface. The appearance ofthe joint should be smooth and smooth.
中埋式止水带采用标准GB18173.2-2000《高分子防水材料止水带》组织生产的。我们可以按用户要求生产各种形状、尺寸的橡胶止水带，还为不同工程、不同部位的需要备有十字型，丁字型、斜度型和内外转角型产品，可适用于任何设计要求。
Medium-buried water-proof belt is organized and produced by thenational standard GB18173.2-2000 "Water-proof Polymer MaterialWater-proof Belt". Therefore, we can produce rubber water stops ofvarious shapes and sizes according to user's requirements. Inaddition, we also have cross-shaped, T-shaped, inclined andinternal and external corner products for different engineering anddifferent parts, which can be applied to any designrequirements.
1.中埋式橡胶止水带这是一种主要用于在混凝土变形缝、伸缩缝等混凝土内部设置的止水带产品，具有以橡胶材料弹性和结构形式来适应混凝土伸缩变形的能力。本产品是利用橡胶的高弹性和压缩变形性，在各种荷载下产生弹性变形，从而起到紧固密封有效地防止建筑构件的漏水，渗水，并起到减震缓冲作用可确保工程建筑物的使用
1. Medium-buried rubber waterproof belt is a kind of waterproofbelt product which is mainly used in concrete deformation joints,expansion joints and other concrete interiors. It has the abilityto adapt to concrete expansion deformation in the form ofelasticity and structure of rubber material. This product utilizesthe high elasticity and compressive deformation of rubber toproduce elastic deformation under various loads, so as to tightenand seal effectively to prevent the leakage and seepage of buildingcomponents, and to play the role of shock absorption and cushioningto ensure the service life of Engineering buildings.
2.中埋式橡胶止水带分类:
2. Classification of buried rubber water stop belts:
从结构形式上可分为CB型止水带和CP型止水带两种。
The structure can be divided into two types: CB type water stopbelt and CP type water stop belt.
CB型止水带是指中间有孔的中埋式止水带，可分为CB型橡胶止水带、CB型塑料止水带两类。主要适用于各种混凝土构筑物的伸缩缝、沉降缝及防震缝等，具有与混凝土锚固紧密、止水密封和适应变形缝伸缩变形的能力*秀等。
CB type water stop belt refers to the buried water stop beltwith holes in the middle, which can be divided into CB type rubberwater stop belt and CB type plastic water stop belt. It is mainlysuitable for expansion joints, settlement joints and anti-seismicjoints of various concrete structures. It has excellent ability toanchor closely with concrete, seal water and adapt to expansion anddeformation of deformation joints.
CP型止水带是指中间无孔的中埋式止水带，可分为CP型橡胶止水带、CP型塑料止水带两种。主要适用于各种变形量不大的混凝土构筑物的施工缝、完全收缩缝、不完全收缩缝、伸缩缝等，具有与混凝土锚固紧密、止水密封及弹性拉伸变形等特点。
The CP type water stop belt refers to the middle buried waterstop belt without holes. It can be divided into two types: the CPtype rubber water stop belt and the CP type plastic water stopbelt. It is mainly suitable for construction joints, completeshrinkage joints, incomplete shrinkage joints and expansion jointsof various concrete structures with small deformation. It has thecharacteristics of tight anchorage with concrete, water seal andelastic tensile deformation.
3.中埋式橡胶止水带的接头方法有两种：
3. There are two kinds of joint methods for buried rubber waterstop belt:
一种是采用粘接剂进行冷接头，一种是使用热硫化模具进行热接。
One is to use adhesive for cold joint, the other is to use hotvulcanization die for hot joint.
粘接剂冷接是采用橡胶止水带专用冷接胶水、采用搭接法把止水带需要接头的断面用磨光机磨平5~10厘米、涂胶水压实即可，具有强度高、凝固快的优点、施工方便、省时省力，可达到一般工程质量要求。
Adhesive cold bonding is to use special cold bonding glue forrubber water stop belt, to use lapping method to grind the sectionof water stop belt which needs joint with a polishing machine for5-10 cm, and to compact with glue water. It has the advantages ofhigh strength, fast solidification, convenient construction,time-saving and labor-saving, and can meet the general engineeringquality requirements.
现场热接硫化法接头是使用与止水带匹配的热硫化模具及生胶片现场硫化热接，施工难度大，但接头效果理想，适合对工程质量要求严格的项目。
On-site hot vulcanization joints are hot vulcanization joints ofhot vulcanization moulds and biofilm matched with water stop belts,which are difficult to construct, but the effect of joints is idealand suitable for projects with strict engineering qualityrequirements.